Search results

I was unable to find the square top plug but got an octagonal one for the moment I drilled a 1/8” hole on the top but I will look for the square top one and replace. For now this one will keep the junk out of the system.

We were a bit nervous about what would be the outcome. Since we found water in the system bad lines in the bilge oil that had been leaking for who knows how long, but yes today I’m going to go get a plastic plug for the upper helm station since they had a pipe nipple connected to a hose and a...

I WOULD LIKE TO TAKE A MOMENT TO THANK ALL THAT RESPONDED AND GAVE ME ADVICE ON THE STEERING LINE ISSUE. THE NEW LINES ARE IN AND PURGED TESTED THE STEERING ALL GOOD. NEW BONDING WIRES ARE IN AND HATCHES ARE CUT.

We have a 41 President Sundeck. The Stove I purchased secondhand from someone in Port Charlotte Fl. But the switch we purchased on eBay. The only difference is that the one that I purchased had a short stem for the nut to lock on to the front of the stove so I switched out that stem with the old...

Definitely now that the floor is up and I have access I will be replacing all bonding wires and terminals.

I was thinking about your advice and my thoughts are possibly making at least one half of the floor removable holding it down with fasteners to the other half thus allowing for access into the bilge. Hopefully never but doable.

Exactly the system was leaking and it should have been fixed. The bilge under the floor was nasty it was traveling forward through the engine room bilge to the bilge pump and since the water heater was bad and leaking they were mixing and being pumped overboard. I kept extracting water with my...

I would love to run them through another location but I’m stuck like chuck on this one not much room.

And thank you for the quick response.

Will do I have a pancake compressor and will push air in from the top helm. The previous owner had a hose hooked to a funnel so he could add oil constantly but it was open to the elements

Good afternoon I am replacing the floor in the aft cabin of our trawler. Under the floor I found the old steering lines that had been worked on by the previous owner and at this point were leaking so I removed them in doing so there was a considerable amount of water that came out I have a...

I'M REPLACING THE FLUID LINES FROM JUST BELOW THE LOWER HELM LEADING TO THE UNIFLOW VALVE I PURCHASED 3000 PSI HYDRAULIC HOSES. SO TO BLEED THE SYSTEM I SHOULD OPEN THE BLEED SCREW ON THE UNIFLOW VALVE WOULD THAT BE CORRECT AND TURN THE WHEEL ON THE FLYBRIDGE

Ok so I tried to test the switch as we discussed and everything checked out per the meter. Since it was already partially disconnected I went ahead and swapped the switch out with the center switch and now the indicator light on the right front burner turns off but now the issue has traveled to...

Thank You for your help. I will try tomorrow when back at the Vessel.

I agree completely that will be a tomorrow thing. Thank you for your input.

Sorry the pictures did not go through

Ok so we turned on the breaker for the Stove/Oven and instantly the indicator light on the right front burner turned on with the switch in the off position. I did check the burners KV’s one by one and found the 2 that were equal so I placed them side by side and the different one in the back. We...

Thank you it looks like the switches are the same so I will try to swap the switch for one of the others to see if the switch is bad. I will post a picture later today when I get to the boat. But it is the switch next to the oven switch. Does the burner’s being switched make a difference we...

Thank you I will try to swap out the switch with one of the others to see if the problem changes so I can test the switch.

Hey good evening. We have a 120 volt 3 burner Stove/Oven. The unit is a Princess model BR 33-7. When we turn on the breaker the indicator light on the right front turns on and does not change when we turn the knob. The left front and the rear center turns on and off and the oven works fine. Any...

Thank You for getting back to me. We recently purchased this vessel and it has no fuel gauge. I am thinking about adding flow meters.

Good morning anybody know approximately what the Fuel Consumption is with twin Ford Lehman SP 135’s