Capt. Fred
Member
I have a 1981 42' Californian LRC with a beautiful cork veneer ceiling in the salon. I need to replace one stip of the veneer. Can anyone tell me where I might find this cork veneer? Thanks for your help. Capt. Fred
Cork Veneer Ceiling
- Thread starter Capt. Fred
- Start date
The friendliest place on the web for anyone who enjoys boating.
If you have answers, please help by responding to the unanswered posts.
If you have answers, please help by responding to the unanswered posts.
Keith
Guru
- Joined
- Oct 5, 2007
- Messages
- 2,715
- Vessel Name
- Anastasia III
- Vessel Make
- Krogen 42
Stuff comes in rolls at most hobby / craft stores.
Capt. Fred
Member
Thanks Keith. I'll check it out tomorrow.
Happy cruising,
Capt. Fred
Happy cruising,
Capt. Fred
RT Firefly
Enigma
Greetings,
Mr. Cf. Wow, cork headliner. Any pictures? I'm intrigued.
Mr. Cf. Wow, cork headliner. Any pictures? I'm intrigued.
x2, I would like to see it as well.
Capt. Fred
Member
I've tried a couple of times to upload a photo but unsuccessful. Sorry. It is a simulated cork paper as described by Larry B. Thanks
RT Firefly
Enigma
Greetings,
That looks petty good. Thanks
That looks petty good. Thanks
Capt. Fred
Member
Cork Ceiling
TG: Your photo is exactly how my ceiling looks. I like mine also and have had a lot of complimentary comments about the way it looks. Do you know where I can purchase more of that material? Thanks for the photo.
TG: Your photo is exactly how my ceiling looks. I like mine also and have had a lot of complimentary comments about the way it looks. Do you know where I can purchase more of that material? Thanks for the photo.
SaucySailoress
Veteran Member
- Joined
- Jan 21, 2013
- Messages
- 50
- Location
- Kuwait
- Vessel Name
- Suzi 4
- Vessel Make
- 30ft Fibreglass SomethingCraft, 1976
That does look very nice!
- Joined
- Apr 15, 2008
- Messages
- 13,738
- Location
- California Delta
- Vessel Name
- FlyWright
- Vessel Make
- 1977 Marshall Californian 34 LRC
Capt Fred,
Have you called Navigator Yachts to ask? My boat was built in Tustin, CA by Marshall Boats. Jule Marshall, the designer/builder, and his son, Gil, still run Navigator/Californian. I called and spoke to Gil about my boat and we had a great conversation with his Dad listening on the speaker from the next desk. Gil recalled being a 15 year old working at his Dad's factory. He was the bilge rat who climbed in the early hulls running wire and plumbing since he was the smallest guy.
They recall much about those early models and might be able to point you toward the vendor. At the very least, you're likely to have a great conversation with the early builders of your boat, if it's a Marshall model.
About - Navigator Yachts, Inc.
Have you called Navigator Yachts to ask? My boat was built in Tustin, CA by Marshall Boats. Jule Marshall, the designer/builder, and his son, Gil, still run Navigator/Californian. I called and spoke to Gil about my boat and we had a great conversation with his Dad listening on the speaker from the next desk. Gil recalled being a 15 year old working at his Dad's factory. He was the bilge rat who climbed in the early hulls running wire and plumbing since he was the smallest guy.
They recall much about those early models and might be able to point you toward the vendor. At the very least, you're likely to have a great conversation with the early builders of your boat, if it's a Marshall model.
About - Navigator Yachts, Inc.
Capt. Fred
Member
Al, Thanks a bunch. My boat is a Marshall boat and I will get in touch with Navigator Yachts. I'll let you know what I find out. Capt. Fred
bren737
Member
- Joined
- Feb 14, 2011
- Messages
- 24
- Vessel Name
- Sandpiper
- Vessel Make
- 34 LRC
I know this is an older thread, but thought it fit the topic if someone is looking for this type of info...
Finally getting around to replacing the old butterscotch vinyl headliner and the nasty carpet and cork that was on the hull walls in the cabin with bead board and trim. Tricky job, as there is NOTHING square or even underneath the old headliner. Basically had to build a substructure of studs to attach the bead board.
Replacing the port lights at the same time with much larger, fully opening ports. Man what a difference in light and airflow they make!! Still have to do the fore cabin... ran out of vacation time....
Cabin Before:
Cabin During:
Cabin after:
Finally getting around to replacing the old butterscotch vinyl headliner and the nasty carpet and cork that was on the hull walls in the cabin with bead board and trim. Tricky job, as there is NOTHING square or even underneath the old headliner. Basically had to build a substructure of studs to attach the bead board.
Replacing the port lights at the same time with much larger, fully opening ports. Man what a difference in light and airflow they make!! Still have to do the fore cabin... ran out of vacation time....
Cabin Before:
Cabin During:
Cabin after:
bren737
Member
- Joined
- Feb 14, 2011
- Messages
- 24
- Vessel Name
- Sandpiper
- Vessel Make
- 34 LRC
dhmeissner
Guru
- Joined
- Sep 26, 2012
- Messages
- 1,569
- Location
- North America
- Vessel Name
- The Promise
- Vessel Make
- Roughwater 35
Nice looking job!
healhustler
Guru
- Joined
- Oct 2, 2009
- Messages
- 5,198
- Location
- USA
- Vessel Name
- Bucky
- Vessel Make
- Krogen Manatee 36 North Sea
Great work. Where did you get the bead board? What finish did you use. Sure did lighten things up.
RT Firefly
Enigma
Sweeeet...
- Joined
- Apr 15, 2008
- Messages
- 13,738
- Location
- California Delta
- Vessel Name
- FlyWright
- Vessel Make
- 1977 Marshall Californian 34 LRC
Very nice, Bren. What an improvement!
dhmeissner
Guru
- Joined
- Sep 26, 2012
- Messages
- 1,569
- Location
- North America
- Vessel Name
- The Promise
- Vessel Make
- Roughwater 35
Not cork, looks like some kind of bamboo treatment but it like it:
bren737
Member
- Joined
- Feb 14, 2011
- Messages
- 24
- Vessel Name
- Sandpiper
- Vessel Make
- 34 LRC
Thanks, all! She's starting to look like one of those fancy Hinckley "lobster boats"... Lord, I hope not. I want it to look good, but not so good that I'm afraid to use it!
It's been tedious work, but not difficult. Worst part is trying to get a somewhat level and squared substructure with the studs. I got the idea from my old Passport 40 sailboat, which had a similar setup.
I used bead board I got at Lowes; 4x8' sheets. Very reasonable. I sealed the back side for added moisture protection and then painted the front side (which was already primed) with a semi-gloss enamel. Filled the areas between the studs with R-Tech insulated sheeting. Should make it a little better insulated and help with moisture control... not that we have an issue with that here on the Gulf Coast, ha!
Like the bamboo thatch, too! Might have considered it if I'd have seen it sooner. The wife likes the added light with the white ceiling and bigger ports.
Al, tried to answer your PM. Hope I did it right!
Bren
It's been tedious work, but not difficult. Worst part is trying to get a somewhat level and squared substructure with the studs. I got the idea from my old Passport 40 sailboat, which had a similar setup.
I used bead board I got at Lowes; 4x8' sheets. Very reasonable. I sealed the back side for added moisture protection and then painted the front side (which was already primed) with a semi-gloss enamel. Filled the areas between the studs with R-Tech insulated sheeting. Should make it a little better insulated and help with moisture control... not that we have an issue with that here on the Gulf Coast, ha!
Like the bamboo thatch, too! Might have considered it if I'd have seen it sooner. The wife likes the added light with the white ceiling and bigger ports.
Al, tried to answer your PM. Hope I did it right!
Bren
healhustler
Guru
- Joined
- Oct 2, 2009
- Messages
- 5,198
- Location
- USA
- Vessel Name
- Bucky
- Vessel Make
- Krogen Manatee 36 North Sea
That bamboo is also very nice, Dave.
Bustlebomb
Senior Member
- Joined
- Feb 2, 2014
- Messages
- 147
- Location
- USA
- Vessel Name
- Snooker (for now.....)
- Vessel Make
- 1981 34 Californian LRC
Bren,
Looks really nice. I made the mistake of showing it to the admiral....you know where that went. Now it's been added to the project list. How did you attach the fir strips? Also, do you have any photos from the outside with the new bigger portlights?
DHM,
Where did you get the bamboo-like material? And how did you attach it?
Looks really nice. I made the mistake of showing it to the admiral....you know where that went. Now it's been added to the project list. How did you attach the fir strips? Also, do you have any photos from the outside with the new bigger portlights?
DHM,
Where did you get the bamboo-like material? And how did you attach it?
markpierce
Master and Commander
- Joined
- Sep 25, 2010
- Messages
- 12,557
- Location
- USA
- Vessel Name
- Carquinez Coot
- Vessel Make
- penultimate Seahorse Marine Coot hull #6
They've already said it.
dhmeissner
Guru
- Joined
- Sep 26, 2012
- Messages
- 1,569
- Location
- North America
- Vessel Name
- The Promise
- Vessel Make
- Roughwater 35
Sorry, didn't mean to mislead anyone. That's not my boat, I'm looking for that material as well.
Sent from my iPad using Trawler
Bustlebomb
Senior Member
- Joined
- Feb 2, 2014
- Messages
- 147
- Location
- USA
- Vessel Name
- Snooker (for now.....)
- Vessel Make
- 1981 34 Californian LRC
DHM,
This looks like it might be what you are looking for:
4' x 8' Lauhala Cabana Tiki Bar Hut Wall Weave Matting | eBay
Matt
This looks like it might be what you are looking for:
4' x 8' Lauhala Cabana Tiki Bar Hut Wall Weave Matting | eBay
Matt
bren737
Member
- Joined
- Feb 14, 2011
- Messages
- 24
- Vessel Name
- Sandpiper
- Vessel Make
- 34 LRC
Bustlebomb...
I know the feeling, except in our house it's when the wife is watching HGTV and says, "Hey, you can do that with our house!".
The studs and strips are adhered with 3M 5200 and stainless screws. On the sheer vertical section in the cabin where the port lights are, the fiberglass is non-cored and very thin (1/8-1/4 inch) so I could only use 5200, no screws. The rest of the ceiling is cored with 1/2 inch (in some places 2 layers thick) plywood, so there's no problem backing up the 5200 with screws. I attached the bead board with nails (thank goodness for air guns!) and then stainless screws along the edges, which are covered up by the trim pieces.
Here's some pics of the port light from outside...
Before:
During:
After:
Cheers!
Bren
I know the feeling, except in our house it's when the wife is watching HGTV and says, "Hey, you can do that with our house!".
The studs and strips are adhered with 3M 5200 and stainless screws. On the sheer vertical section in the cabin where the port lights are, the fiberglass is non-cored and very thin (1/8-1/4 inch) so I could only use 5200, no screws. The rest of the ceiling is cored with 1/2 inch (in some places 2 layers thick) plywood, so there's no problem backing up the 5200 with screws. I attached the bead board with nails (thank goodness for air guns!) and then stainless screws along the edges, which are covered up by the trim pieces.
Here's some pics of the port light from outside...
Before:
During:
After:
Cheers!
Bren
Bustlebomb
Senior Member
- Joined
- Feb 2, 2014
- Messages
- 147
- Location
- USA
- Vessel Name
- Snooker (for now.....)
- Vessel Make
- 1981 34 Californian LRC
Bren,
The portlights look great! Not to hijack the thread but where did you get the portlights? What did you use to cut the fiberglass to fit the new ones? And what did you bed them with? That looks like a great project. I've got to be careful bot to show that one to my wife yet....
Matt
The portlights look great! Not to hijack the thread but where did you get the portlights? What did you use to cut the fiberglass to fit the new ones? And what did you bed them with? That looks like a great project. I've got to be careful bot to show that one to my wife yet....
Matt
- Joined
- Apr 15, 2008
- Messages
- 13,738
- Location
- California Delta
- Vessel Name
- FlyWright
- Vessel Make
- 1977 Marshall Californian 34 LRC
Here's what my 1977 34 LRC Capt's stateroom portlights look like. I thought we all had 2 ports in the cabin.
